Главная страница Случайная страница
КАТЕГОРИИ:
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатикаИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханикаОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторикаСоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансыХимияЧерчениеЭкологияЭкономикаЭлектроника
CAUTION _____
|
|
Do not put shim stock under the shim. This may cause the shim to pop out al high rpm, causing extensive engine damage. Do not grind the shim. This may cause it to fracture, causing extensive engine damage.
VALVE CLEARANCE ADJUSTMENT CHART INLET VALVE
| PRESENT SHIM | f— | — Example | |||||||||||||||||||
| PART No. (92180 -) | юзе | ||||||||||||||||||||
| MARK | 7Б | ||||||||||||||||||||
| THICKNESS (mm) | 2.50 | 2.SB | 2.80 | 2.65 | 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.96 | 3.00 | 3.06 | 3.10 | 3.16 | 3.20 | 3.25 | 3.30 | 3.36 | 3.40 | 3.45 | 3.50 |
| 2.50 | 2.56 | 2.60 | - 2.65 | 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.95 | 3.00 | 3.06 | 3.10 | 3.15 | 3.20 | 3.26 | 3.30 | ||||
| У | 2.50 | 2.55 | 2.80 | 2.85 | 2.70 | 2.76 | 2.80 | 2 85 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.16 | 3.20 | 3.25 | 3.30 | 3.35 | ||
| 2.50 | 2.55 | 2.60 | 2.85 | 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.95 | 3.00 | 3.06 | 3.10 | 3.16 | 3.20 | 3.25 | 3.30 | 3.36 | 3.40 | ||
| 2.50 | 2.55 | 2.60 | 2.65 | 2.70 | 2.75 | 2.80 | 2.86 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | |
| SPECIFIED CLEARANCE/NO CHANGE REQUIRED | ||||||||||||||||||||
| 2.55 | 2.80 | 2.85 | 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | |
| 2.60 | 2.85 | 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.95 | 3.00 | 3.06 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | ||
| 2.65 | 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.95 | 3.00 | 3.06 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | |||
| 2.70 | 2.75 | 2.80 | 2.85 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | ||||
| 2.75 | 2.80 | 2 85 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.45 | 3.50 | ||||||
| 2.80 | 2.86 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.50 | |||||||
| 2.85 | 2.90 | 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.36 | 3.40 | 3.45 | 3.50 | / | ||||||
| 2.90 | 2.95 | 3.00 | 3.06 | 3.10 | 3.16 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | У | |||||||
| 2.95 | 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | |||||||||
| 3.00 | 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | ||||||||||
| 3.05 | 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | |||||||||||
| 3.10 | 3.15 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | ||||||||||||
| 3.16 | 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | \ | ||||||||||||
| 3.20 | 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | \INSTALL THE SHIM OF THIS THICKNESS (mr | |||||||||||||
| 3.25 | 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | |||||||||||||||
| 3.30 | 3.35 | 3.40 | 3.45 | 3.50 | ||||||||||||||||
| 3.35 | 3.40 | 3.45 | 3.50 | |||||||||||||||||
| 3.40 | 3.46 | 3.50 | ||||||||||||||||||
| 3.45 | 3.50 | |||||||||||||||||||
| 3.50 |
o^o
1. Measure the clearance (when engine is cold).
2. Check present shim size.
3. Match clearance in vertical column with present shim size in horizontal column.
4. Install the shim specified where the lines intersect This shim will give the proper clearance.
Example: Present shim is 3.05 mm
Measured clearance is 0.35 mm Replace 3.05 mm shim with 3.20 mm shim.
5. Remeasure the valve clearance and readjust if necessary.
____________ CAUTION________________
Be sure to remeasure the clearance after selecting a shim according to the table. Tlie clearance can be out of the specified range because of the shim tolerance.
NOTE
| 0.00 | 0.03 | ||
| 0.04 | 0.08 | ||
| 0.09 | 0.13 | ||
| 0.14 | 0.17 | ||
| 0.18 | 0.23 | ||
| £ | 0.24 | 0.28 | |
| 0.29 | 0.33 | ||
| I | 0.34 | 0.38 | |
| 0.39 | 0.43 | ||
| H | 0.44 | 0.48 | |
| ш Ш tr | 0.49 | 0.53 | |
| 0.64 | 0.68 | ||
| Э V) | 0.59 | 0.83 | |
| 111 5 Ш | 0.64 | 0.68 | |
| 0.89 | 0.73 | ||
| Z -J о | 0.74 | 0.78 | |
| 0.79 | 0.83 | ||
| 0.84 | 0.88 | ||
| HI > | 0.89 | 0.93 | |
| < > | 0.94 | 0.98 | |
| 0.99 | 1.03 | ||
| 1.04 | 1.08 | ||
| 1.09 | 1.13 | ||
| 1.14 | 1.18 | ||
| 1.19 | 1.23 |
О If the valve clearance is..smaller (larger) than the standard, select a thinner (thicker) shim and then measure the clearance again.
